Forgot password

Bottom paint redux

  • June 20, 2014 8:16 AM
    Quote
    Message # 1562637
    Anonymous member
    Sorry.... I know this has been asked about a million times already and I wish could find the posts so I wouldn't have to ask it again.

    About how much bottom paint is required per coat for a W32?
  • June 20, 2014 6:30 PM
    Quote
    Reply # 1562688 on 1562637
    Anonymous member (Administrator)
    Mike: 
    Of course it depends on how thick etc but I usually rough sand the existing and apply one good coat and I recall using a gallon and 2 qts with a little left over.  
    It has been 3 years so memory may be off... 

    Jay
  • June 21, 2014 2:48 AM
    Quote
    Reply # 1562701 on 1562637
    Deleted user
    Mike,

    I've always bought two gallons of hard paint (non-ablative). Good coverage without skimping and about a quart or less left over.

    Werner
  • June 21, 2014 5:40 AM
    Quote
    Reply # 1562706 on 1562637
    Anonymous member
    I know there are variables (brushed or rolled etc.) which makes it hard to estimate.

    That's my problem. I'll be starting from a 'bare hull' and looking to apply oh, at least 2, maybe 3 good coats of ablative.

    Sounds like I should factor about an average of 1 1/2 gallon per coat. More to start, maybe less at the end.
    Last modified: June 21, 2014 5:41 AM | Anonymous member
  • June 21, 2014 6:42 AM
    Quote
    Reply # 1562708 on 1562637
    Anonymous member (Administrator)

    "Bare hull" does this mean gel coat?  if so look in to applying barrier coat first.

     
  • June 22, 2014 4:34 AM
    Quote
    Reply # 1562735 on 1562637
    Anonymous member
    Essentially, since I'm switching from a hard paint to an ablative.

    so yep... that too
    Last modified: June 22, 2014 4:37 AM | Anonymous member
  • June 29, 2014 6:34 PM
    Quote
    Reply # 3034710 on 1562637
    Deleted user

    I just put only ONE gallon of Micron 66 on my bottom. Practical sailor just did a review of bottom paints and it seemed to be the best for my purpose of actively cruising. I plan on doing a shake down cruise for a few months and so I wasn't all that concerned about having a thick coat as I will be putting a new coat on after I launch later in the year. I will let you know the results in a few months to see if I made the right decision or not. What I wanted to convey was, that this paint was like no other paint I have ever come across. It really did a number on the rollers and brushes I was using by tearing them all up and I had to use 2 face masks mitigate the odor.
  • June 30, 2014 3:39 AM
    Quote
    Reply # 3034873 on 1562637
    Deleted user

    Just a small side note about using a face mask while painting...  Be aware that there are different types of masks for different threats.  If you are dealing with dust (sanding) you need a system that will keep particulate matter out.  If you are dealing with fumes (painting), you need a system that filters out the vapors (organic compounds).  They are different.  The little hospital type masks that you buy at the local hardware stores will not protect you.  You need either a full face mask or half mask (depending on the project) that has replaceable filter cartridges - and use the proper filter cartridge.

    Example at:

    http://solutions.3m.com/wps/portal/3M/en_US/3M-PPE-Safety-Solutions/Personal-Protective-Equipment/Products/Product-Catalog/?N=8690968+3294529207+5023214&rt=r3



    Last modified: June 30, 2014 7:55 PM | Anonymous member (Administrator)
Powered by Wild Apricot Membership Software